|
|
Navigation:
CCP Home > Products
> Heat-Shrinkable Pipe & Pipeline Protection
Products
Navigation:
CCP Home > Products
>
Moisture Sealing Products
CANUSA Wrapid Bond™
A viscous-elastic adhesive based
system for pipeline corrosion protection
| Wrapid Bond™ is a
wraparound corrosion protective coating consisting of a
modified and reinforced visco-elastic adhesive applied
onto a polyethylene carrier film. Supplied in roll form,
Wrapid Bond™ provides effective corrosion protection by
providing a barrier to water and oxygen. Wrapid Bond™ is
for use on aboveground and underground pipelines. |
Features & Benefits
- Adhesion & Creep
Resistance: The specially formulated adhesive bonds
tenaciously to even the most difficult substrates and provides good
elevated temperature creep resistance and resistance to soil stresses.
Improved soil stress resistance is achieved with the installation of
WrapidCoat™ outer wrap.
- Wide Range of Applications:
Wrapid Bond™ is ideally suited for a
diverse range of pipeline applications including: coating repair on new
pipeline construction; transition areas from above to below ground
pipelines; special sections such as bends, tees, flanges, etc.;
rehabilitation of existing pipelines.
- Long-Term Corrosion Protection: The thick layer of adhesive provides a
tough barrier to water and oxygen which provides effective corrosion
protection.
- Saves Time & Money:
- Long shelf-life
(does not harden)
- Various widths
available with convenient roll lengths for ease of
inventory
- Fast installation
with excellent adhesion on steel and many other base
surfaces without
applying primer
- Self-healing ability
when slightly damaged due to plastic-elastic
properties
- No drying or
hardening time
- Impermeable to water
and oxygen
- Part of a Complete Line of Wrapid™ Products:
CANUSA-CPS products
such as Wrapid Sleeve™, CanusaWrap™,
CanusaTube™, and
Wrapid Tape™ have been oil, gas and civil infrastructure industry
standards for many years. The Wrapid Bond™ product
line also includes a supplementary outer wrap,
Wrapid Coat™. The outer wrap provides supplementary
soil stress resistance.
|
Typical Product Properties
|
|
Property |
Test Standard |
Unit |
|
Thickness |
Measured |
> 1.8
mm |
|
Density |
ASTM D792 |
1.1 -
1.3 g/cm3 |
|
Impact
Resistance* |
EN
12068 |
15
J |
|
Indentation Resistance* |
EN
12068 |
0.60
mm remaining (pass) |
|
Peel Strength* |
EN
12068 |
>
0.5 N/mm cohesive failure |
|
Lap Shear
Strength |
EN
12068 |
0.02
N/mm2 |
|
Glass
Transition Temperature |
ASTM D3418 |
< -20°C |
|
Cathodic Disbondment Resistance* |
ASTM
G8/EN 12068 |
2 mm at
23°C |
|
Cathodic Disbondment Resistance* |
ASTM
G42/EN 12068 |
1 mm at
60°C |
|
Electrical
Resistance* |
EN
12068 |
> 108
ohm/m2 |
|
Unwinding Test
at -30°C |
EN
12068 |
No
separation, tears or cracks |
|
Low Temperature
Flexibility at -30°C |
EN
12068 |
No
separation, tears or cracks |
|
Water
Absorption |
ASTM
D570 |
< 0.05% |
|
Drip Resistance |
EN
12068 |
Pass at
90°C |
| * When used with
Wrapid Coat™
Product
Selection Guide |
| * Wrapid Coat™ is
required for buried applications. |
Wrapid Bond™ Ordering Guide
|
|
Designation |
Contents |
Quantity
/ Carton |
| WRB-B 50-10
BL |
50 mm x 10
m |
12 |
| WRB-B
100-10 BL |
100 mm x 10
m |
6 |
| WRB-B
150-10 BL |
150 mm x 10
m |
4 |
| WRB-B
200-20 BL |
200 mm x 20
m |
2 |
| WRB-B
100-30 BL |
100 mm x 30
m |
12 |
| WRB-B
150-30 BL |
150 mm x 30
m |
6 |
|
