AnodeFlex Splice Kits for 1500 Linear Anode System

Includes In-Line, End Cap & Tee Splice Kits
  • AnodeFlex 1500 In-Line Splice Kit

    Product Description

    The AnodeFlex 1500 In-Line Splice Kit is designed to connect together two AnodeFlex 1500 anode
     strands to a lead wire.

    The heat-shrinkable tubing, sealant and accessories, have been specifically designed to environmentally protect the electrical connection in direct burial soil applications during the whole anode life.

    The long term performance of AnodeFlex 1500 is conditional upon keeping the base copper conductor and electrical connection isolated from water. Only AnodeFlex splice kits are recommended for any connection to AnodeFlex 1500. The sealing performance has been tested for over 5 years of real time accelerated tests. Our field and lifetime experience with this product now exceeds 20 years.

    The heat-shrinkable components are made of a radiation-crosslinked polymer. The cable and anode are wrapped with mastic, which flows when heated to ensure a very tight seal. When the sleeve is heated with a torch, or a heat gun, it shrinks tightly around the anode. Once installed, the In-Line Splice kit withstands the normal wear and tear of a construction environment and is extremely corrosion resistant. Impact, internal pressure and penetration resistance have all been tested following the telecommunication requirements for telephone cable splices. The installation is easy and can be completed in few minutes by a trained technician.

    Contents of AnodeFlex 1500 In-Line Splice Kit
      

    Quantity

    Description

    1 each
    1 each
    1 each
    1 each
      
    1 each
    1 each

    Installation instructions.
    Abrasion paper to clean the conductive polymer surface.
    Chlorine and low pH resistant tie wraps to contain coke within fabric.
    Aluminum tape covered with adhesive for use as thermal protection
    of AnodeFlex fabrics during installation.
    Electrical grade sealing mastic.
    Uncoated heat shrinkable tubing to cover, seal and reinforce splice.

      
    Typical Kit Component Dimensions for AnodeFlex 1500 In-Line Splice

      

    Description

    Type dimension

    Requirement in mm (in)

    Abrasion paper

    Width x Length

    50 x 150 mm (1.97" x 5.90")

    Tie wraps

    Length

    170 mm (6.69") min.

    Aluminum tape

    Width x Length

    50 x 150 mm (1.97" x 5.90")

    Sealing mastic strip

    Width x thickness x length

    50 x 3 x 600 mm
    (1.97" x 0.12" x 23.62")

    Heat shrinkable tubing

    Length

    400 ± 10 mm (15.75" ± 0.39")

    Inside diameter supplied

    50 mm (1.97") min.

    Inside diameter recovered

    16 mm (0.63") max.

    Wall thickness recovered

    2 mm (0.079") min.

      
    Typical Kit Component Dimensions for AnodeFlex 1500 In-Line Splice

      
    Property Condition Requirement

    Internal pressure resistance
    External pressure resistance
    Corrosion Resistance
    Impact
    Penetration

    23°C, 1 Bar, 24 hrs
    23°C, 10 Bar, 24 hrs
    23°C
    23°C, 100 Nm, blunt blade
    23°C, 72 hrs, needle
    dia. 18 mm, 2.5 kg

    No leakage
    No water ingress
    Pass
    Pass with 25 kV
    Pass with 25 kV

      
    Ordering Information

    AnodeFlex 1500 In-Line Splice Kit, Part Number 196502-000.

  • AnodeFlex 1500 End Cap Splice Kit

    Product Description

    The AnodeFlex 1500 End Cap Splice kit is designed to seal the exposed end of an AnodeFlex 1500 anode circuit.

    The heat-shrinkable tubing, sealant and accessories, have been specifically designed to environmentally protect the termination in direct burial soil applications during the entire anode life.

    The long term performance of AnodeFlex1500 is conditional upon keeping the base copper conductor and electrical connections isolated from water. Only AnodeFlex End Splice kits are recommended for any AnodeFlex 1500 circuit termination. The sealing performance has been tested for over 5 years of real time accelerated tests. Our field and lifetime experience with this product now exceeds 20 years.

    The heat-shrinkable components are made of a radiation-crosslinked polymer. The cable and anode are wrapped with mastic, which flows when heated to ensure a very tight seal. When the cap and sleeve are heated with a torch, or a heat gun, they shrink tightly around the anode. Once installed, the End Cap Splice kit withstands the normal wear and tear of a construction environment and is extremely corrosion resistant. Impact, internal pressure and penetration resistance have all been tested following the telecommunication requirements for telephone cable splices.

    The installation is easy and can be completed in few minutes by a trained technician.

    Contents of AnodeFlex 1500 End Cap Splice Kit
      

    Quantity Description

    1 each
    1 each
    1 each
    1 each
      
    1 each
    1 each
    1 each

    Installation instructions.
    Abrasion paper to clean the conductive polymer surface.
    Chlorine and low pH resistant tie wraps to contain coke within fabric.
    Aluminum tape covered with adhesive for use as thermal protection
    of AnodeFlex fabrics during installation.
    Electrical grade sealing mastic.
    Heat shrinkable uncoated end seal boot.
    Uncoated heat shrinkable tubing to cover, seal and reinforce splice.

      
    Typical Kit Component Dimensions for AnodeFlex 1500 End Cap Splice

      

    Description

    Type dimension

    Requirement in mm (in)

    Abrasion paper

    Width x Length

    50 x 150 mm (1.97" x 5.90")

    Tie wraps

    Length

    170 mm (6.69") min.

    Aluminum tape

    Width x Length

    50 x 150 mm (1.97" x 5.90")

    Sealing mastic strip

    Width x thickness x length

    50 x 3 x 250 mm
    (1.97" x 0.12" x 9.84")

    End Cap

    Length

    57mm (2.24") min.

    Inside diameter (as supplied)

    22 mm (0.87") min.

    Inside diameter (fully recovered)

    7 mm (0.28") max.

    Heat shrinkable tubing

    Length

    150 ± 10 mm (5.90" ± 0.39")

    Inside diameter supplied

    50 mm (1.97") min.

    Inside diameter recovered

    16 mm (0.63") max.

    Wall thickness recovered

    2 mm (0.079") min.

      
    Typical Kit Component Dimensions for AnodeFlex 1500 End Cap Splice

      
    Property Condition Requirement

    Internal pressure resistance
    External pressure resistance
    Corrosion Resistance
    Impact
    Penetration

    23°C, 1 Bar, 24 hrs
    23°C, 10 Bar, 24 hrs
    23°C
    23°C, 100 Nm, blunt blade
    23°C, 72 hrs, needle
    dia. 18 mm, 2.5 kg

    No leakage
    No water ingress
    Pass
    Pass with 25 kV
    Pass with 25 kV

      
    Ordering Information

    AnodeFlex 1500 End Cap Splice Kit, Part Number 762546-000.


  • AnodeFlex 1500 Tee Splice Kit

    Product Description

    The AnodeFlex 1500 Tee Splice kit is designed for 3-way connections of the AnodeFlex 1500 anode strand and lead wire(s).

    The splice consists of a heat shrinkable tee boot, factory installed over a crimped 3-way connection of anode lead wire double coated with a high-molecular-weight polyethylene insulation. Field installation of the splice simply entails crimping AnodeFlex anode(s) or lead wire(s) to each of the three legs of the tee, and sealing each connection with mastic and a heat-shrinkable sleeves.

    The heat-shrinkable tubing, sealant and accessories, have been specifically designed to environmentally protect the electrical connection in direct burial soil applications during the entire anode life. The long term performance of AnodeFlex 1500 is conditional upon keeping the base copper conductor and electrical connection isolated from water. Only AnodeFlex Tee Splice kits are recommended for any 3-way combination connection to AnodeFlex 1500.

    The sealing performance has been tested for over 5 years of real time accelerated tests. Our field and lifetime experience with this product now exceeds 20 years.

    The heat-shrinkable components are made of a radiation-crosslinked polymer. The cable is wrapped with mastic, which flows when heated to ensure a very tight seal. When heated with a torch, or a heat gun, the sleeves shrink tightly around the anode. Once installed, the Tee Splice kit withstands the normal wear and tear of a construction environment and is extremely corrosion resistant. Impact, internal pressure and penetration resistance have all been tested following the telecommunication requirements for telephone cable splices. The installation is easy and can be completed in few minutes by a trained technician.

    Contents of AnodeFlex 1500 Tee Splice Kit
      

    Quantity Description

    1 each
    1 each
    1 each
    1 each
      
    1 each
    1 each
    1 each
    1 each

    Installation instructions.
    Abrasion paper to clean the conductive polymer surface.
    Chlorine and low pH resistant tie wraps to contain coke within fabric.
    Aluminum tape covered with adhesive for use as thermal protection
    of AnodeFlex fabrics during installation.
    Electrical grade sealing mastic.
    Heat shrinkable uncoated end seal boot.
    Uncoated heat shrinkable tubing to cover, seal and reinforce splice.
    Three-layer Tee molded part.

      
    Typical Kit Component Dimensions for AnodeFlex 1500 Tee Splice

      

    Description

    Type dimension

    Requirement in mm (in)

    Abrasion paper

    Width x Length

    50 x 150 mm (1.97" x 5.90")

    Tie wraps

    Length

    170 mm (6.69") min.

    Aluminum tape

    Width x Length

    50 x 150 mm (1.97" x 5.90")

    Sealing mastic strip

    Width x thickness x length

    50 x 3 x 1400 mm
    (1.97" x 0.12" x 55.12")

    Heat shrinkable tubing

    Length

    400 ± 10 mm (5.90" ± 0.39")

    Inside diameter supplied

    50 mm (1.97") min.

    Inside diameter recovered

    16 mm (0.63") max.

    Wall thickness recovered

    2 mm (0.079") min.

      
    Typical Kit Component Dimensions for AnodeFlex 1500 End Cap Splice

      
    Property Condition Requirement

    Internal pressure resistance
    External pressure resistance
    Corrosion Resistance
    Impact
    Penetration

    23°C, 1 Bar, 24 hrs
    23°C, 10 Bar, 24 hrs
    23°C
    23°C, 100 Nm, blunt blade
    23°C, 72 hrs, needle
    dia. 18 mm, 2.5 kg

    No leakage
    No water ingress
    Pass
    Pass with 25 kV
    Pass with 25 kV

      
    Ordering Information

    AnodeFlex 1500 Tee Splice Kit, Part Number 557280-000.