Isomate by Lamons

The Isomate™ sealing/isolating gasket is designed for basic applications where electrical flange isolation and corrosion control are required on pipes containing water/wastewater, gas, natural gas, oil and other hydrocarbon based medias up to 175ºF(79ºC).
  • Description

    The Isomate™ sealing/isolating gasket is designed for basic applications where electrical flange isolation and corrosion control are required on pipes containing water/wastewater, gas, natural gas, oil and other hydrocarbon based medias up to 175ºF(79ºC). Available for flat face and raised face joint flanges from 1/2" to 24", ANSI 150-300#. The Isomate gasket is an economical solution for basic performance. Isomate sealing/isolating gasket consists of a Phenolic retainer faced on both sides with Nitrile rubber material.

     

     

    RETAINER MATERIALS

    • Phenolic

     

    GASKET/RETAINER MATERIAL SPECIFICATIONS

     

    ASTM

    TEST METHOD

    Rubber Faced Phenolic

    D149

    Dielectric Strength Volts/Mil Short Time

    500

    D695

    Compressive Strength (psi)

    25,000

    D570

    Water Absorption (%)

    1.60

    D790

    Flexural Strength (psi)

    22,500

    D256

    IZOD Impact Strength (Ft-lbs/Inch)

    1.20

    D638

    Tensile Strength (psi)

    20,000

    D732

    Shear Strength (psi)

    10,000

    D952

    Bond Strength (lb)

    1,500

     

    Temperature - Operating

    -65°F (-54°C) to +175°F (+79°C)

     

    NOTE: Operating Temperature for Gaskets and Flange Isolation Kits is based off the Gasket Retainer Temperature. Seal element temperature does not dictate the min. and max. gasket operating temperature.

     

    SEAL ELEMENT MATERIALS

    • Nitrile
  • Features

    • Sealing and isolating gasket.

     

    APPLICATIONS

    • Isomate™ gaskets are engineered to provide reliable sealing and electrical isolation for a wide variety of applications.

     

    The industry has improved sealing technology in retainer type gaskets with engineered seal elements and groove designs. Defender™ and IsoGuard™ sealing systems should be reviewed, specified and used when a long-term maintenance-free solution is necessary.

     

    INDUSTRIES

    • Water/Wastewater
    • Oil
    • Gas

     

    MEDIA

     

    Water

    • Potable Water
    • Sea Water
    • Wastewater

     

    Energy

    • Natural Gas
    • Gasoline
    • Crude Oil
    • Propane
    • Nitrogen

     

    GENERAL INSTALLATION TIPS

    1. Always use proper safety equipment.
    2. Installation should be done with a torque wrench or stud tension measuring device.
    3. Lamons packaged product to inspect and determine that components are as specified.
    4. Flanges shall be free of pits, gouges, rust, debris, oil and grease. Surface finish shall be no greater than 250 RMS.
    5. Check bolts and nuts to ensure they are clean.


    OTHER INFORMATION

     

         

     

     

  • Specifications

    SEAL ELEMENT MATERIAL SPECIFICATIONS

     

    Sealing Element

    Temperature - Operating

    Nitrile

    -40°F (-40°C) to +250°F (+121°C)

     

     

    CONFIGURATIONS FOR GASKET TYPE AND SLEEVE AND WASHER SETS

     

             

    Type "E" Gasket
    Fits over the bolt holes and extends to the O.D. of the flange to assist contractors as the bolt holes automatically center the gasket. Provides excellent protection against shorting out of the corrosion mitigation hardware.

     

    Type "F" Gasket
    Fits within the bolt hole circle of the flange and extends to the I.D. of the bolt circle providing good protection against shorting out of the corrosion mitigation hardware.

     

    "E" or "F" Type Gaskets
    The Isomate gasket is available in a Type "E" or "F" configuration to accommodate all your sealing/isolating needs.

     

     

    Single Washer Set
    One isolation sleeve, one steel washer and one insulating washer for each stud/bolt.

     

    Double Washer Set
    One isolation sleeve, two steel washers and two insulating washers for each stud/bolt.

     

    SUGGESTED SLEEVE/WASHER SET

     

    ED = Economy (Mylar Sleeves, Steel ZP Washers and Phenolic Washers) - Double Washer Set