H50 Gray Tape Cold-Applied Coating by Tapecoat

Cold-applied above and below ground coating in tape form.
SKU
Tapecoat H50 Gray Tape Cold-Applied Coating
Grouped product items
Product Name Qty
H50 Gray Tape, 4" x 50' Rolls, 6 Rolls/Case, by Tapecoat
$419.50
M50RC Gray Tape, 6" x 50' Rolls, 4 Rolls/Case, by Tapecoat
$321.01
H50 Gray Tape, 2" x 50' Rolls, 12 Rolls/Case, by Tapecoat
$419.50
M50RC Gray Tape, 4" x 50' Rolls, 6 Rolls/Case, by Tapecoat
$321.01
M50RC Gray Tape, 2" x 50' Rolls, 12 Rolls/Case, by Tapecoat
$321.01
H50 Gray Tape, 6" x 50' Rolls, 4 Rolls/Case, by Tapecoat
$419.50
Basic Use

Tapecoat H50 Gray is designed to protect above ground, buried or submerged metal surfaces from corrosion and electrolysis. It is used for coating pipe, pipe joints, fittings, couplings, tanks, pipe type cable, conduit, tie rods, elevator casings and other metal surfaces. Its unique "MAF" film backing has been specially formulated to provide strength that allows it to be pulled tightly around fittings and other irregular shapes with minimal pull back due to memory. Tapecoat H50 Gray is resistant to UV rays, thermal expansion, impact, abrasion and can be applied over a wide range of ambient temperatures.


Composition

Tapecoat H50 Gray is composed of a Gray specially formulated multipolymer alloy film "MAF" with a synthetic elastomeric adhesive. Blended in the adhesive is an integrated primer. This primer is kept from permanently bonding to its backing (while in the roll) by a tough, easily removed polymer release liner which prevents contamination of the primer and adhesive prior to its use.


Technical Data

Color

Gray

Weight per carton

38 lbs

Shelf life

Rotate stock yearly

Standards

AWWA C-209

Recommended for use

With Coal Tar, Polyethylene, Polypropylene, 
Epoxy and Urethane Plant Coatings

Low temp flex

Excellent

Bacteria resistance

Excellent

Thickness

50 ± 2 mils

Tests

ASTM D522-93, ASTM G22, ASTM D1000

Surface Preparation

Surface must be clean and dry. SSPC-SP3 Power Tool Cleaning is recommended to remove any loose rust and scale, dust or dirt. A "Tack Cloth" for removal of fine dust particles is provided in each carton. Oil, grease and all other residue are to be removed from pipe surface per SSPC-SP1 Solvent Cleaning. SSPC-SP 6 Commercial Blast Cleaning is also acceptable.

Primer Application

Because H50 Gray comes with an "integrated primer" built into the tape, normal liquid primers are not required. However, if the application is taking place in periods of extreme cold (below 40°F) a liquid primer will enhance the immediate bond. TC Omniprime is the compatible primer for use with Tapecoat H50 Gray. Apply primer to the prepared surface by brush at the rate of approximately 300 square feet per gallon. Let primer dry before applying Tapecoat H50 Gray.

Tape Application

  • Spiral Wrap: Tapecoat H50 Gray is applied by removing the release liner and spirally wrapping in a single thickness with a continuous overlap of tape. Tension in wrapping should be enough to obtain conformability to the surface being coated.
       
  • Cigarette Wrap: Precut strips of Tapecoat H50 Gray to a length equal to the circumference of the pipe plus a minimum of 4". Follow general tape application instructions described above.

NOTE: Tapecoat 2025 (Terra Shield) Rockshield is recommended in areas where soil stress is expected.